Items marked "In stock" are shipped:
- ordered by 10:00 on the same day
- ordered after 10:00 the next day

Revolutionary portable charger Type 1 | max. 3,7kW

Code: PCHT1-S2
Sale New Tip
Brand: EVtun
430 € –8 %
evtun accelev
430 € –8 % 395 € 477,95 € incl. VAT
Not available

Accelev v2 is a processor-controlled, advanced AC portable charger with features not available in other chargers. Includes grid monitoring (power shedding) and BatteryCare™. It is updatable and expandable via USB port and can be flexibly completed according to customer wishes.

We believe that Accelev v2 is the most modern portable charger of our times.

Detailed information

Product detailed description

Forget about stupid, simple charging cables. We live in the 21-st century! It is not an “ordinary” EVSE or charging cable.

With the unique ability to charge speed reducing, when another load is detected – your tripping breakers will be history.

Battery Balancing procedure may increase the usable capacity of your battery and state of health (SOH) – perfect for Nissan Leaf and Jaguar i-Pace, Audi eTron battery balancing improvement.

Use the touchscreen, update new functions via USB.

Monitor the health of your home energy grid with a spectacular SOP (State of Power) parameter. Be safe and protected while charging your car.

This EVSE/electric car charger can be flexibly completed according to customer wishes.

We believe that Accelev v2 is the most modern EVSE/ “wallbox” of our times.

Grid monitoring – immediate charging speed reduction while other load detected – no more fuse switches keeping turning off

BatteryCare™ – unique full charging / no full charging modes with maximum life protection for your battery

Updateable – flash most recent firmware via micro USB extension port.

2.8 inch touch screen – human interface with „geek mode” – you can monitor all parameters while loading.

If you like to learn more and read more technical explanations of functions – read the manual.


Main Screen

Values, Statuses (from top left):

BatteryCare – BatteryCare option status
NoFull – no full charge option status
GridM – grid monitoring (shedding) status
234/250V – voltage of shedding / actual voltage
24/12.8A – actual max. amperes / actual amperage
25C – core of charger temperature
02:12:34 – total charging time
3.569kWh – total kWh charged
3.2kW – actual charging power
Battery symbol – shows phase of charging and if BatteryCare is on or off
MAX 24A – max. amperes permitted
­ [+] – change max. amperes: 6, 9, 12, 15, 18, 21, 24
Start – starts charging or idle, resets counters
Setup – opens Setup screens.

BatteryCare(TM) – enables and disables BatteryCare routines and functions
No Full Charging – self described, perfect for battery life.
ReVive Balancing – a special pulse balancing of battery to cure and recover lost capacity.

Grid Mon – enables and disables grid monitoring (shedding)
More Sens – more sensitive grid monitoring
­ [+] – sets level of grid monitoring
234V – actual prediction for power shedding start
01 – tolerance of grid monitoring (01 = smallest gap, quickest reaction)

Grid monitoring depends on actual voltage in your electric grid. It is a good idea to set it more conservative. 08 is a factory setting, good for most situations. It will give about 15V gap between idle and reaction to load at 240V, and an approximately 8V gap at 210V. Increasing tolerance is increasing the gap by 1-2V (depending on actual voltage). A higher step can be observed at higher voltages, as this method of grid load control based on actual voltage to estimate load. Decreasing reduces the gap by 1-2V. In the case of electric fuses turned off please decrease tolerance first. If you see, that charger reacts to load and reduces the speed of charging, but this amperage reduction is not enough for your fuse system – please switch “More Sens” on to increase the amount of amperage reduction by twice.

S/N: F2610001 – serial number of charger
F/V: 2.0 – firmware version installed
Total Energy – global energy counter
Reset – resets global energy counter
Firmware Update – switches to boot mode, waits for update via USB port
Umax – highest voltage ever measured
Imax – highest amperage ever measured
Tmax – highest temperature ever measured


1. What is a typical setup of charger you suggest?
We highly suggest to use BatteryCare with No Full Charging for everyday use and commuting, and BatteryCare without No Full Charging for occasional, long trip occurrences. Charging battery full, along with it’s high temperature reduces usable capacity and State Of Health of your battery.

2. Can I restart ReVive balancing again after it finished to balance and cure my battery even more?
Yes, this is ok and it will work for you.

3. Can I use Accelev outdoors?
Yes, it is waterproof.

4. Can I charge Type1/Type2/Tesla US cars with one charger?
Yes. You need just cables we provide. Tesla US connector, Mennekes (Type 2) and J1772 (Type 1) are available. Your charger is delivered with one of these types. If you want more – ask us.

5. Can I have longer/shorter cables for supply/car connection?
Of course. Just tell us what do you need and we will produce that.



Additional parameters

Category: Choose by car
Weight: 4 kg
Charging mode: 3 (with static load allocation), otherwise Mode 2
Functions: BatteryCare (deactivated in factory settings), NoFull charge, Grid Monitoring, Current Boost
Input voltage range: 200 ~ 240 V (AC)
Power supply: 1 phase
Rated max. current: 16A
Rated power: up to 3,7 kW
User interface: 2,8" TFT colour - touch screen display
Material: PC + GFS
Cable length: 5 meters
Dimensions: 180 x 130 x 77mm
Degree of protection: IP54
Operating temperature: - 30°C ~ + 50°C
Connector - Car: Type 1 | "Yazaki"
Connector - Station: Schuko
Used: Indoor / Outdoor

Grid Monitoring

How to update

Soft Start

Be the first who will post an article to this item!

Only registered users may post articles. Please log in or register.